序号 |
课 程 名 称 |
天 数 |
1 |
Introduction to Pro/ENGINEER (PRO/E基础培训) |
5天 |
2 |
Fundamental of drawing(工程图) |
5天 |
3 |
Pro/E应用环境配置 |
4天 |
4 |
Advanced surfacing (基本曲面培训) |
2天 |
5 |
Fundamentals of Sheet Metal Design(钣金设计培训课程) |
2天 |
6 |
Fundamentals of Mechanism Design(机构运动设计) |
2天 |
7 |
Design Animation (设计动画) |
1天 |
8 |
PhotoRender (基本渲染培训) |
1天 |
9 |
TOP-DOWN Design (高级装配和自顶向下设计) |
3天 |
10 |
Introduction to ISDX (交互式曲面培训) |
3天 |
11 |
Pro/INTRALINK Muti-site系统管理员培训 |
5天 |
12 |
Pro/INTRALINK Single-site系统管理员培训 |
3天 |
13 |
Pro/INTRALINK用户培训 |
2天 |
14 |
Pro/MECHANICA结构及热力学分析培训 |
5天 |
15 |
Fundamentals of Mechanism Dynamics(运动分析基础) |
2天 |
16 |
Pro/MOLDESIGN Training(模具设计培训课程) |
3天 |
17 |
PLASTIC ADVISOR 塑料流动分析培训 |
1天 |
18 |
EMX Training(模具专家系统培训) |
3天 |
19 |
PDX Training(级进模具设计培训) |
2天 |
20 |
EFX Training(钢结构设计培训) |
3天 |
21 |
Fundamentals of milling(铣削加工基础) |
3天 |
22 |
Fundamentals of Turning(车削加工基础) |
2天 |
23 |
Pro/SHEETMETAL Manufacturing(钣金加工基础) |
2天 |
24 |
五轴加工培训 |
5天 |
25 |
NC模块与机床的连接(三轴铣削机床或两轴车削机床) |
根据型号确定 |
26 |
NC模块与机床的连接(五轴铣削机床或车铣联合机床) |
根据型号确定 |
27 |
Diagramming with RS Designer(布线图设计) |
2天 |
28 |
Pro/ENGINEER Cable Harness Design(布线设计培训课程) |
4天 |
29 |
Pro/PIPING Training(管路设计培训课程) |
3天 |
30 |
Pro/CONCEPT(概念设计培训课程) |
3天 |
31 |
PhotoLUX (高级渲染培训) |
2天 |
32 |
Introduction to Restyle(逆向工程培训) |
2天 |
33 |
Behavioral Modeling Training(行为建模培训) |
2天 |
34 |
ISODRAW 培训 |
5天 |
35 |
MATHCAD 培训 |
3天 |
36 |
Tolerance Analysis Training(公差分析培训) |
1天 |
37 |
ECAD-MCAD Training(ECAD-MCAD 培训) |
1天 |
38 |
Pro/ENGINEER Wildfire 升级培训 |
2天 |
39 |
INTRALINK 或PDMLINK 快速实施培训 |
20天 |
40 |
PTC软件现场答疑 |
协商 |